Fiber Drawing Machine – Consider This..

This automatic visual Fiber tensile testing system is designed for operator skill independent utilization in creation and lab settings. Two basic design configurations allow the user to choose between a set up for regular linear Proof testing and with additional mandrels for rotary high strength testing.

The linear version is made for production Proof testing with forces approximately 22 N. Motorized clamps with carefully developed rubber inserts ensure that the FTTH Cable Production Line will not be ruined in the screening process whilst at the same time eliminating the need for an external air provide. Degrees of pulling force, tugging speed and hold time are automated and easily available to the operator through the built in LCD touch-screen manage. Information from tests can be saved and accessed via the USB port or Ethernet user interface.

Mandrels of the same style as in NYFORS’ optical Fiber recoaters can be easily mounted on the Proof tester inside the rotary higher strength configuration. The Fiber is wrapped round the two mandrels which support it having a unique clamping system. This way greater loads can be employed to the Fiber, allowing breaking up strength assessments below managed circumstances.

Adjustable clamp placement facilitates screening with the greatest force levels as well as screening of short Fiber lengths. The lightweight and light bodyweight style definitely makes the instrument easy to move around in a lab environment and to incorporate in a production work bench in which space reaches reduced. The device is actually a lightweight and lightweight tool suitable for screening the effectiveness of visual materials up to 30 N. The equipment is created to meet all types of applications where a strength test needs to be performed.

The machine is designed using the user in mind. The Optical Fiber Proof-Testing Machine is easily put into the guided linear clamps, and also the testing starts automatically with a “One Touch” go switch. The built-in microprocessor regulates all of the important parameters such as tugging force, pulling speed and hold time. This enables for any completely managed check each time.

The equipment can be connected to an outside PC, which enables access to all automated parameters and configurations. The machine is adapted to face-alone use or to the incorporation into different subsystems. The device comes with an substantial capacity for signing and conserving details including pulling force, pulling speed and Fiber size along with other guidelines.

Two recoat injector configurations can be purchased. The PTR307 utilizes a computerized pump to inject the recoat material. The amount of materials dispensed by the automated injector is managed by hand via the top-installed “Inject” button or programmed in to the device using the tablet controller. The PTR307B includes a handbook recoat shot program that needs the consumer to personally distribute the recoat materials into the mold cavity; a substitute injector for your PTR307B recoater can be obtained below. Please note the automated injector is just suitable for high-directory recoat material, while the manual injector is compatible with both reduced- and- index recoat materials; both are marketed separately below. Make sure you get in touch with Technology Support for more information.

he handbook injector can be mounted to suitable Fiber recoaters via the 4-40 anchoring screws on the recoater housing (see picture to the right). Utilize a 3/32″ hex key to secure the injector just before use. To connect the PTRRRM for the recoater mold, tighten the connector at the conclusion of the eco-friendly plastic tubes, then loosen by a 1/4 choose allow for rotation.

The injector is equipped with a syndication valve and two-position selection lever for directing the stream of recoat material. A knurled dispensing attach with an internal plunger behaves as a syringe for that recoat material. To fill up the syringe, point the lever downward (i.e., towards the recoat container), then rotate the knurled dispensing attach counterclockwise until it rotates easily to fill the syringe (shown inside the photo towards the right). Then, to inject the recoat materials to the mold, point the lever horizontally (i.e., facing qyjflh knurled screw) and spin the screw clockwise until near the finish in the travel range is reached. Steer clear of bottoming the dispenser because this may harm the inner plunger; also be careful when re-engaging the threads to prevent go across threading the dispensing attach. Several fill up/inject steps may be required till air is displaced inside the system. Use lens tissue and an acetone or alcoholic beverages cleansing solution to collect FTTH Cable Production Line material that flows from your mold.

Leave a Reply

Your email address will not be published. Required fields are marked *